16v Mini Club Forums  

Go Back   16v Mini Club Forums > Builds > Honda Builds

Reply
 
Thread Tools Display Modes
Old 21-03-2017, 08:54 AM   #31
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default

Quote:
Originally Posted by GEORDIE SP1 View Post
Hi, Have you made your rear driveshafts yet, wondering what length your getting, mine are working out about 465mm, Cheers.
I made them already! there is 30mm difference in left and right because the diff output is not in the centre of the diff housing. so, you put the diff output in the centre line of the car so your prop shaft is in the centre so 1 driveshaft is shorter then the other, about 30/35 mm.
AWD is offline   Reply With Quote
Old 28-03-2017, 02:17 PM   #32
Brumski
Senior Member
 
Join Date: Jul 2008
Location: Warrington, Cheshire
Posts: 1,152
Subframe: MTB
CC: 1800
Make: Honda
ECU: Mini Tec uprated Honda
Default

Nice. Was the rear diff easy enough to do? What seals did you replace or was it a full stripdown?

Sent from my SM-G930F using Tapatalk
Brumski is offline   Reply With Quote
Old 28-03-2017, 02:23 PM   #33
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default

Quote:
Originally Posted by Brumski View Post
Nice. Was the rear diff easy enough to do? What seals did you replace or was it a full stripdown?

Sent from my SM-G930F using Tapatalk
Not a full strip, wasnt needed.. no play in the diff so replaced only the driveshaft seals and the propshaft seal out of precaution. it sucks to have to do that when everything is nice and tight under the car
AWD is offline   Reply With Quote
Old 28-03-2017, 02:26 PM   #34
Brumski
Senior Member
 
Join Date: Jul 2008
Location: Warrington, Cheshire
Posts: 1,152
Subframe: MTB
CC: 1800
Make: Honda
ECU: Mini Tec uprated Honda
Default

Agreed. It's a job I'll do for sure before the final fitment of the diff.

Sent from my SM-G930F using Tapatalk
Brumski is offline   Reply With Quote
Old 28-03-2017, 02:30 PM   #35
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default

Quote:
Originally Posted by Brumski View Post
Agreed. It's a job I'll do for sure before the final fitment of the diff.

Sent from my SM-G930F using Tapatalk
its a 30 min job and about 35 euro's.. no reason not to do it anyways
AWD is offline   Reply With Quote
Old 01-04-2017, 10:05 PM   #36
Bennjaminozhonda
Senior Member
 
Join Date: Apr 2013
Posts: 213
Subframe: Allspeed
Default

Great setup

Did you consider any other rear diff - considering the crv job is a hydraulic clutch pack thing which is stupidly complicated - or did you strip the internals etc?
Bennjaminozhonda is offline   Reply With Quote
Old 02-04-2017, 04:07 PM   #37
DVO
Senior Member
 
DVO's Avatar
 
Join Date: Oct 2009
Location: Noordwijkerhout, Netherlands
Posts: 508
Subframe: Home Made
CC: 1298
Make: Suzuki
ECU: Chipped
Default

Sent you a private message

Dennis
DVO is offline   Reply With Quote
Old 03-04-2017, 03:45 PM   #38
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default

Quote:
Originally Posted by Bennjaminozhonda View Post
Great setup

Did you consider any other rear diff - considering the crv job is a hydraulic clutch pack thing which is stupidly complicated - or did you strip the internals etc?
i am using the crv-1 diff, its mechanical. the later models have a hydraulic system and you dont want to use that
AWD is offline   Reply With Quote
Old 04-04-2017, 08:00 AM   #39
Oz
Senior Member
 
Oz's Avatar
 
Join Date: Oct 2003
Location: Jersey, Channel Islands
Posts: 4,104
Subframe: Other
CC: 1595
Make: Honda
ECU: DTA
Default

Quote:
Originally Posted by AWD View Post
Have you tried your fuel rail on there yet ? It may just be the angle of the picture but the inlet looks tight enough to the head to foul the fuel rail
__________________
New subframe fitting has begun - slowly

Build Thread - Standard Round Nose with K series subframe build begun
Oz is offline   Reply With Quote
Old 04-04-2017, 10:08 AM   #40
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default

Quote:
Originally Posted by Oz View Post
Have you tried your fuel rail on there yet ? It may just be the angle of the picture but the inlet looks tight enough to the head to foul the fuel rail
Its the picture.. all fits just fine! i have build this mini already 2 times to make sure everything fits the way i want to.
AWD is offline   Reply With Quote
Old 04-04-2017, 10:33 AM   #41
Oz
Senior Member
 
Oz's Avatar
 
Join Date: Oct 2003
Location: Jersey, Channel Islands
Posts: 4,104
Subframe: Other
CC: 1595
Make: Honda
ECU: DTA
Default

Cool
__________________
New subframe fitting has begun - slowly

Build Thread - Standard Round Nose with K series subframe build begun
Oz is offline   Reply With Quote
Old 01-05-2017, 11:33 AM   #42
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default














Not much to do at this moment.. just a few little thing here and there.. waiting for the body to come back from paint! All other things are done, prepared and ready to build the mini for the 3rd and last time

Last edited by AWD; 01-05-2017 at 11:37 AM.
AWD is offline   Reply With Quote
Old 17-05-2017, 10:02 AM   #43
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default



















just little bits and pieces.. the tank is almost done! Received a few boxes from the UK.. nice! everything is here to finish the mini when i gets back from the painter.. takes forever btw..
AWD is offline   Reply With Quote
Old 29-05-2017, 09:07 AM   #44
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default





Tank is done!

Made the front shafts now in a different way. Made new (mini) splines on the honda shafts.. not easy but it works very well! So, no more joints!

AWD is offline   Reply With Quote
Old 13-06-2017, 05:59 AM   #45
AWD
Senior Member
 
Join Date: Feb 2017
Location: The Netherlands "Haarlem"
Posts: 104
Default

primer, slow going.. still needs a lot of work... another 3 weeks and i hope its all done

AWD is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 03:23 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.