16v Mini Club Forums  

Go Back   16v Mini Club Forums > Search Forums

Showing results 1 to 25 of 434
Search took 0.02 seconds.
Search: Posts Made By: keitht
Forum: Wanted 28-06-2018, 01:17 PM
Replies: 4
Views: 122
Posted By keitht
No doesn't effect operation, its design for very...

No doesn't effect operation, its design for very cold conditions so that it doesn't freeze, not really a problem. It doesn't have to be blanked just the pipes looped together. I think i just put a...
Forum: Wanted 28-06-2018, 10:53 AM
Replies: 4
Views: 122
Posted By keitht
You don't need to run coolant through the IACV, I...

You don't need to run coolant through the IACV, I looped the pipes and blanked the bottom of the valve.
Forum: Wanted 27-06-2018, 08:31 PM
Replies: 4
Views: 173
Posted By keitht
PM'd

PM'd
Forum: Wanted 27-06-2018, 07:55 AM
Replies: 4
Views: 173
Posted By keitht
Yes this is what I need, Are you selling?

Yes this is what I need, Are you selling?
Forum: Wanted 25-06-2018, 11:53 AM
Replies: 4
Views: 173
Posted By keitht
Wiper Mechanism

Hi Guys, I need the above for my build must be in good working order, I have a motor but would take all if for sale. Let me know what you have. Thanks
Forum: Wanted 22-06-2018, 08:37 AM
Replies: 6
Views: 232
Posted By keitht
Its just a loop between 2 pins at the ECU, i...

Its just a loop between 2 pins at the ECU, i don't have the wiring diagram at the minute but can have a look later.
Forum: Wanted 21-06-2018, 08:34 PM
Replies: 6
Views: 232
Posted By keitht
It can be bypassed if that helps. I took mine off.

It can be bypassed if that helps. I took mine off.
Forum: Honda Builds 19-06-2018, 08:10 PM
Replies: 29
Views: 1,183
Posted By keitht
They're not going to fall out anyway!! I used 2mm...

They're not going to fall out anyway!! I used 2mm plate as well. Good work.
Forum: Honda Builds 12-06-2018, 01:57 PM
Replies: 402
Views: 70,064
Posted By keitht
The rest of the body in 2 pack epoxy, Primer...

The rest of the body in 2 pack epoxy, Primer next.

https://farm1.staticflickr.com/964/41780692632_01e5bf84f7_b.jpg

https://farm1.staticflickr.com/907/41106198544_974acb212c_b.jpg
...
Forum: Honda Chat 11-06-2018, 08:38 AM
Replies: 5
Views: 193
Posted By keitht
Have you got a fuel pressure gauge on the rail...

Have you got a fuel pressure gauge on the rail and what ECU are you using?
Forum: Honda Builds 25-05-2018, 11:42 AM
Replies: 402
Views: 70,064
Posted By keitht
With the interior finished we could move on to...

With the interior finished we could move on to the exterior prep, as with the interior I wanted a few good coats of epoxy mastic before final paint to protect as much as possible. We started by...
Forum: Honda Chat 19-05-2018, 10:13 AM
Replies: 5
Views: 279
Posted By keitht
PM'd

PM'd
Forum: Honda Chat 18-05-2018, 07:25 AM
Replies: 5
Views: 279
Posted By keitht
Ricky Evans Motorsport will post no problem, I...

Ricky Evans Motorsport will post no problem, I got a few recently to NI.
Forum: Honda Chat 11-05-2018, 08:16 AM
Replies: 11
Views: 1,475
Posted By keitht
Yes you can configure vtec engagement criteria...

Yes you can configure vtec engagement criteria with the S300.
Forum: Honda Chat 11-05-2018, 08:11 AM
Replies: 9
Views: 601
Posted By keitht
2.5" for me.

2.5" for me.
Forum: Honda Builds 10-05-2018, 07:51 AM
Replies: 402
Views: 70,064
Posted By keitht
Before moving on to the exterior of the car I...

Before moving on to the exterior of the car I decided to blank off the windscreen vents and ashtray hole in the dash rail, I did this for a number of reasons the main being that I couldn’t...
Forum: Honda Builds 16-04-2018, 09:58 AM
Replies: 402
Views: 70,064
Posted By keitht
With all the interior welding finished and...

With all the interior welding finished and everything trial assembled the interior could be sprayed. The roof was first then the rear of the floor, rear seats and quarters. The roof had some surface...
Forum: Honda Builds 26-03-2018, 02:04 PM
Replies: 402
Views: 70,064
Posted By keitht
I did a quick trial with it and I'm happy with...

I did a quick trial with it and I'm happy with the heat and flow, its a million times better than standard and half the size. People use the below unit from T7 design and seem to be happy. The rad is...
Forum: Honda Builds 26-03-2018, 11:33 AM
Replies: 402
Views: 70,064
Posted By keitht
Apologies for the lack of updates, Lots going on....

Apologies for the lack of updates, Lots going on. For the interior heater I played with a few ideas I even ordered a T7 single fan unit but the wrong one was delivered so I decided to make my own....
Forum: Honda Chat 05-03-2018, 08:06 PM
Replies: 10
Views: 555
Posted By keitht
Have you got any pictures? Incorrect assembly can...

Have you got any pictures? Incorrect assembly can cause them to fail.
Forum: Honda Chat 16-01-2018, 07:51 PM
Replies: 27
Views: 963
Posted By keitht
I had a similar issue and it turned out to be the...

I had a similar issue and it turned out to be the coil in the distributor, Make sure you have all the signals required from the VR sensors, theres a good video on youtube that might help, I'll have a...
Forum: Honda Chat 10-01-2018, 03:45 PM
Replies: 3
Views: 544
Posted By keitht
Fuel hose and jubilee clips will be fine, Max...

Fuel hose and jubilee clips will be fine, Max pressure will be about 3.5bar.
Forum: Honda Builds 05-01-2018, 11:39 AM
Replies: 402
Views: 70,064
Posted By keitht
With the servo fitted I could fit the new brake...

With the servo fitted I could fit the new brake master and measure for the connecting brake lines, See details of exactly what I ordered from Furore Products, keep in mind these are to connect to the...
Forum: Honda Builds 02-01-2018, 10:42 AM
Replies: 402
Views: 70,064
Posted By keitht
Back to the engine bay, the last part of the...

Back to the engine bay, the last part of the braking system was the servo and master. I bought a new master as I got it at a very good price and the old one had some ware in the bore so it couldn’t...
Forum: Honda Builds 28-12-2017, 02:15 PM
Replies: 402
Views: 70,064
Posted By keitht
I understand now, Its not something that I...

I understand now, Its not something that I considered but makes sense, I assumed the Allspeed design was strong enough and I haven't seen any modified in this way. I intend to make my own frame in...
Showing results 1 to 25 of 434

 
Forum Jump

All times are GMT. The time now is 05:36 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.